Shoe-In - Concrete Finishing Shoe - Smooth, No Spikes - - Available in Medium, Large and Extra Large
Concrete Finishing & Resinous Floor Coating Shoes Flat Style - For Concrete Installation. No Tread Marks Or Heel Marks. Ideal For Decorative Concrete Stamping And General Surface Troweling.
It's Never Been Easier To Install Epoxy Coatings Or Self-Leveling And Decorative Overlays. With A Patented Design, Shoe-In® Pro Shoes Are A Fantastically Simple And Affordable Solution With Multiple Applications. Applications Include: Installing Epoxy Coatings | Installing Concrete & Screed Floors Including Decorative Overlays Industrial Environments | Renovations Or Removals | Any Area Where Flooring Needs Protecting
Slips On In Seconds - Hands Free! Put An End To Frustrations With Straps, Buckles And Adjustments On Traditional Floor Finishing Shoes. Comfortable - Goes Over Your Existing Shoes Or Boots. Stays Snug Whether YouRe Standing Or Kneeling. Wide Base For Stability. Time Saving - Allows You To Take Protective Shoes On And Off As Needed To Get The Job Done.
Sizing: Small: Fits Boot Size 8 And Under, Sneaker Size 8 And Under Medium: Fits Boot Size 8 - 9, Sneaker Size 8 - 9 Large: Fits Boot Sizes 10 To 11, Sneaker Size 10 To 12 Extra-Large: Fits Boot Sizes 12 To 16, Sneaker Size 13 To 16
Shoe-In - Spiked Shoes for Resinous Coatings with 3/4In Sharp Spikes - Small - (^fitz Boot Size 8 and Under, Sneaker Size 8 and Under) - [v2_shoe_in-small]...more info
Shoe In - 3/4in Sharp Spiked Shoes For Resinous Coatings- Small
Shoe-In - Spiked Shoes for Resinous Coatings with 3/4In Sharp Spikes - Available in Small, Medium, Large and Extra Large
Concrete Finishing & Resinous Floor Coating Shoes Sharp Spiked Style - For Resinous / Epoxy Floor Coating Installation. Mark-Free Installations. Sharp Or Rounded Replacement Spikes Are Available.
It's Never Been Easier To Install Epoxy Coatings Or Self-Leveling And Decorative Overlays. With A Patented Design, Shoe-In® Pro Shoes Are A Fantastically Simple And Affordable Solution With Multiple Applications. Applications Include: Installing Epoxy Coatings | Installing Concrete & Screed Floors Including Decorative Overlays Industrial Environments | Renovations Or Removals | Any Area Where Flooring Needs Protecting
Slips On In Seconds - Hands Free! Put An End To Frustrations With Straps, Buckles And Adjustments On Traditional Floor Finishing Shoes. Comfortable - Goes Over Your Existing Shoes Or Boots. Stays Snug Whether YouRe Standing Or Kneeling. Wide Base For Stability. Time Saving - Allows You To Take Protective Shoes On And Off As Needed To Get The Job Done.
Sizing: Small: Fits Boot Size 8 And Under, Sneaker Size 8 And Under Medium: Fits Boot Size 8 - 9, Sneaker Size 8 - 9 Large: Fits Boot Sizes 10 To 11, Sneaker Size 10 To 12 Extra-Large: Fits Boot Sizes 12 To 16, Sneaker Size 13 To 16
Shoe-In - Sponge Finishing Shoe - Available in Medium, Large and Extra Large
Sponge Finishing Style, for Concrete Installation.
No Tread Marks or Heel Marks. Ideal for Decorative Concrete Stamping and General Surface Troweling
BEST PRACTICES FOR REMOVAL AND CARE OF SPONGES FOR SHOE-IN SPONGE FINISHING SHOES
The sponges are designed to be removed from the shoe after each use and can be used multiple times if properly removed and cleaned after each usage. SPONGE REMOVAL: slide your thumb between the Velcro on the sponge and the Velcro on the base of the shoe and gently pull off as depicted in the image. Do not remove the sponge by pulling only on the white section of the sponge, this will increase the likelihood of separating the Velcro from the sponge. SPONGE CLEANING: clean the sponge with warm soapy water. Press the sponge flat to remove excess water and lay the sponges flat to dry. Do not ‘twist’ or ‘wring out’ the sponge, this can cause the sponge to tear and separate the Velcro from the sponge. Sizing: Small: Fits Boot Size 8 And Under, Sneaker Size 8 And Under Medium: Fits Boot Size 8 - 9, Sneaker Size 8 - 9 Large: Fits Boot Sizes 10 To 11, Sneaker Size 10 To 12 Extra-Large: Fits Boot Sizes 12 To 16, Sneaker Size 13 To 16
Replacement Straps For 46106, 46107, 46108, 46110 & 46112 (set Of 4 - 2 Each Shoe)
Shoe-In - Replacement Sponges (Pair) for 46191, 46192, 46193
Sponge Finishing Style, for Concrete Installation.
No Tread Marks or Heel Marks. Ideal for Decorative Concrete Stamping and General Surface Troweling
BEST PRACTICES FOR REMOVAL AND CARE OF SPONGES FOR SHOE-IN SPONGE FINISHING SHOES
The sponges are designed to be removed from the shoe after each use and can be used multiple times if properly removed and cleaned after each usage. SPONGE REMOVAL: slide your thumb between the Velcro on the sponge and the Velcro on the base of the shoe and gently pull off as depicted in the image. Do not remove the sponge by pulling only on the white section of the sponge, this will increase the likelihood of separating the Velcro from the sponge. SPONGE CLEANING: clean the sponge with warm soapy water. Press the sponge flat to remove excess water and lay the sponges flat to dry. Do not ‘twist’ or ‘wring out’ the sponge, this can cause the sponge to tear and separate the Velcro from the sponge. Sizing: Small: Fits Boot Size 8 And Under, Sneaker Size 8 And Under Medium: Fits Boot Size 8 - 9, Sneaker Size 8 - 9 Large: Fits Boot Sizes 10 To 11, Sneaker Size 10 To 12 Extra-Large: Fits Boot Sizes 12 To 16, Sneaker Size 13 To 16